A/T - Choosing the Right ATF
TRANSMISSION: ALL
BULLETIN: # 9002006
SUBJECT: Automatic Transmission Fluid
DATE: Feb 1990
AUTOMATIC TRANSMISSION FLUID
CHOOSING YOUR ATF
Different ATF's (Automatic Transmission Fluid) can have different frictional properties which can produce different shift characteristics. You may
have already experienced problems like lock-up shudder, or squawks on shifts and have corrected them by changing the fluid. This alone tells, you
that friction material and fluids are critical in today's cars.
MEETING THE O.E.M. SPECIFICATIONS
The first thing to consider when choosing an ATF is "Does it meet the O.E.M. specification?" ATF's wishing to be labeled as DEXRON II and/or
MERCON must first meet the respective minimum requirements. It's important to note that even though the specification for DEXRON II and
MERCON are currently very similar, THEY ARE NOT IDENTICAL. Also note, even fluids which meet the same specification may not be
identical. One fluid may just meet a specification and, another may far surpass it. You should know what your fluids properties are! You can get
that information from your fluid supplier.
EVALUATING YOUR FLUID
Ask your supplier to prove (certify) that the fluid meets O.E.M. specifications (MERCON OR DEXRON II). He will do that by supplying you with
the license (certification) number issued to him by the O.E.M.
1982 Volvo 240 L4-2127cc 2.1L SOHC B21F Copyright ? 2013, ALLDATA 10.52SS Page 70
A DEXRON-II license number (sometimes referred to as a "D" number) will always start D-2. A typical DEXRON license number can be seen in
Figure 2.
MERCON license numbers will be six digits starting with M as shown in Figure 3..
TRY TO MEET SEVERAL SPECIFICATIONS!
DEXRON II and MERCON have different minimum specifications, so a product that meets BOTH specifications may be better then those meeting
only one spec. Meeting other specs, in addition to the first two can be an added benefit. If a fluid is licensed as DEXRON II AND MERCON as
well as others like Allison C-4, or Caterpillar TO-2/TO-4, it means the fluid had to pass more tests and may be a better fluid.
Lastly, demand that the license numbers be placed on all your invoices especially if you buy in bulk. If your supplier is unwilling, it is very likely
that they are supplying you an unlicensed fluid. Licensed suppliers are required to supply the license numbers to their customers as part of their
agreement with the O.E.M.
OTHER THINGS TO CHECK
So now you've narrowed your choices down to a few suppliers that have O.E.M. license numbers. How do you compare two fluids that meet the
same O.E.M. Spec.? Ask your supplier to give you the viscometrics on the fluid you buy.
An excellent "bench mark of the overall quality of a fluid is its viscosity at -40 degrees. This is measured in "centipoise" or "cPs". DEXRON II
specification says viscosity will be no more then 50,000 cPs @ - 40 degrees. (Some poor fluids have tested at over 1,000,000 cPs) In general, the
lower the number, the better the fluid.
Keep in mind that as the number goes down the price of the fluid usually goes up. (You get what you pay for) Most good fluids will average around
1982 Volvo 240 L4-2127cc 2.1L SOHC B21F Copyright ? 2013, ALLDATA 10.52SS Page 71
35,000 cPs. Hydrotreated (or Hydrocracked) fluids average around 20,000 cPs or less. (Hydrotreating is a refining process done to the base oil to
clean out contaminants or impurities) Synthetic ATF's average 10,000 cPs or less, and some are as low as 5000 cPs. Viscosity at -40 degrees is a
function of the base stock from which the ATF is made. A low number indicates a premium base oil OR an expensive refining process.
(Hydrotreating)
FOR ADDITIONAL INFORMATION:
Transmission Digest August '89
Page 91 December '89 Page 51
BULLETIN RECAP
^ Only use fluids with O.E.M. approvals.
^ Try to get a fluid that meets more than one spec (e.g DEXRON II AND MERCON)
^ Check the viscosity at -40 degrees. The lower the number the better.
^ Avoid bargain basement fluids with no license numbers.
Comments
Post a Comment